Network Adapter Allied Telesyn 2700FTX

Discussion in 'Linux Networking' started by Achim Lindt, Feb 5, 2004.

  1. Achim Lindt

    Achim Lindt Guest

    Hello,

    I have some Problems with the atnic module for my AT Network Adapter AT
    2700 FTC (SC).

    I've downloaded and compiled the atnic.c module from the knowledge-Base at
    www.alliedtelesyn.com and installed the module, following the
    Instructions in the README file.

    After rebooting, the module seems to load correctly.
    No error messages:pcnet32_probe_pci: found device 0x001022.0x002000
    ioaddr=0x005800 resource_flags=0x000101
    eth0: PCnet/FAST+ 79C972 at 0x5800, 00 30 84 6d dc 3b
    tx_start_pt(0x0c00):~220 bytes, BCR18(9861):BurstWrEn BurstRdEn
    NoUFlow
    SRAMSIZE=0x1700, SRAM_BND=0x0800,
    pcnet32: pcnet32_private lp=c2df9000 lp_dma_addr=0x2df9000 assigned
    IRQ 9.
    pcnet32.c:v1.25kf 26.9.1999
    <<

    The Problem: Only the Copper-Port on the Card is working!
    The Lightwave-Port (SC) doesen't work! When I reboot the computer, I
    can see a green Diode flashing, indicating a working connection. But
    when the module is loaded by the Boot-Procedure the light stops
    flashing. The light goes out.
    When I connect the Computer with a Twisted Pair Ethernet Cable on the
    copper Port, everything is working fine.


    The compile command was:
    gcc -D__KERNEL__ -DMODULE - DMODVERSIONS -I/lib/modules/2.4.20-
    4GB/build/include -I/lib/modules/2.4.20-4GB/build/include/net -Wall -
    Wstrict-prototypes -O6 -march=i486 -c atnic.c

    During the compilation I get the following warnings:

    -----OUTPUT OF GCC ------
    gcc: 2: No such file or directory
    In file included
    from/lib/modules/2.4.20-4GB/build/include/linux/tqueue.h:19,
    from /lib/modules/2.4.20-4GB/build/include/linux/aio.h:4,
    from /lib/modules/2.4.20-4GB/build/include/linux/fs.h:201,
    from /lib/modules/2.4.20-4GB/build/include/linux/capability.h:17,
    from /lib/modules/2.4.20-4GB/build/include/linux/binfmts.h:5,
    from /lib/modules/2.4.20-4GB/build/include/linux/sched.h:10,
    from atnic.c:21:
    /lib/modules/2.4.20-4GB/build/include/asm/system.h:n function
    `__set_64bit_var':
    /lib/modules/2.4.20-4GB/build/include/asm/system.h:189: warning:
    dereferencing type-punned pointer will break strict-aliasing rules
    /lib/modules/2.4.20-4GB/build/include/asm/system.h:189: warning:
    dereferencing type-punned pointer will break strict-aliasing rules
    In file included
    from /lib/modules/2.4.20-4GB/build/include/linux/netdevice.h:147,
    from atnic.c:35:
    /lib/modules/2.4.20-4GB/build/include/linux/skbuff.h:
    In function `__pskb_pull':
    /lib/modules/2.4.20-4GB/build/include/linux/skbuff.h:856: warning:
    comparison between signed and unsigned
    /lib/modules/2.4.20-4GB/build/include/linux/skbuff.h: In function
    `pskb_may_pull':
    /lib/modules/2.4.20-4GB/build/include/linux/skbuff.h:872: warning:
    comparison between signed and unsigned
    atnic.c: In function `pcnet32_probe1':
    atnic.c:696: warning: comparison between signed and unsigned
    ------END---------------

    But the module is compiled --> atnic.o

    In the output of 'dmesg', there is an error message:NETDEV WATCHDOG: eth0 transmitt timed out
    eth0:transmit timed out, status 007b, resetting
    <<

    The /ect/modules.conf entry is:alias eth0 atnic
    options atnic options=0
    <<
    options=0 is for Auto-nego
    The Card is installed in our Linux/Samba Fileserver,
    a Fuijitsu-Siemens "Primergy Econel 30", Intel Pentium4, 512 MB RAM.
    The OS is Suse Linux 8.2, Kernel: 2.4.20-4GB,
    GCC Version is 3.3, GNU C Library stable release version 2.3.2

    I had to recompile the module because the atnic.o module I found on
    the website was compiled with an gcc Version 2 and thus, the module
    will not work with my gcc Version 3.

    I've tested the Lightwave-connection with a Windows-Computer and a
    AT27001FTC-SC Adapter and it worked fine.

    I hope, You can help me with this problem!

    Thanks in advance !!!

    Achim Lindt


    P.S. Please excuse my Enlgish, I hope You can understand everything.
    P.P.S. Sorry for cross-posting. F'up to computer.os.linux.hardware
     
    Achim Lindt, Feb 5, 2004
    #1
    1. Advertisements

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.