Networking Forums

Networking Forums > Wireless Networking > Wireless Internet > WRT54G and a WPC54G

Reply
Thread Tools Display Modes

WRT54G and a WPC54G

 
 
Jeff
Guest
Posts: n/a

 
      06-10-2004, 08:43 PM
Hi,

Is anyone aware of a problem using a Linksys WPC54G wireless card on
Windows 2000 Professional? When I tried to configure the system,
there was absolutely no signal being received on my notebook (as seen
in the WLAN Monitor)

Also, the 'Connect' and 'Refresh' buttons in the WLAN Monitor were
dimmed out.

Another clue: when I first installed the driver, I got 'ErrorCode=-3
Incorrect data or not enough disk space' (although there was tons of
disk space)

However, the driver did appear to install, and when I checked the
hardware profile, it said the device was running properly.

I just used a vanilla setup (Infrastructure Mode, Channel 6,
SSID=linksys etc)

thanks
 
Reply With Quote
 
 
 
 
Lars M. Hansen
Guest
Posts: n/a

 
      06-11-2004, 10:44 AM
On 10 Jun 2004 13:43:56 -0700, Jeff spoketh

>Hi,
>
>Is anyone aware of a problem using a Linksys WPC54G wireless card on
>Windows 2000 Professional? When I tried to configure the system,
>there was absolutely no signal being received on my notebook (as seen
>in the WLAN Monitor)
>
>Also, the 'Connect' and 'Refresh' buttons in the WLAN Monitor were
>dimmed out.
>
>Another clue: when I first installed the driver, I got 'ErrorCode=-3
>Incorrect data or not enough disk space' (although there was tons of
>disk space)
>
>However, the driver did appear to install, and when I checked the
>hardware profile, it said the device was running properly.
>
>I just used a vanilla setup (Infrastructure Mode, Channel 6,
>SSID=linksys etc)
>
>thanks


It sometimes freaks out during install. Uninstall the software, reboot
and try again.

Lars M. Hansen
http://www.hansenonline.net
(replace 'badnews' with 'news' in e-mail address)
 
Reply With Quote
 
snowdog512
Guest
Posts: n/a

 
      12-31-2004, 01:36 PM

Jeff:

Did you ever get this resolved? I'm trying to setup the same
configuration (WRT54G, WPC54G, Win2000) and can't get past that
ErrorCode = -3 problem.

As you said, it installed the drivers for the card but I don't have the
signal monitor available to me nor am I getting a signal on my card.

thanks,
mike


--
snowdog512
brought to you by http://www.wifi-forum.com/

 
Reply With Quote
 
snowdog512
Guest
Posts: n/a

 
      12-31-2004, 05:28 PM

Hey

I seemed to have overcome my problem. I posted a writeup under "Les
than Positive Experience installing Linksys WPC54G/WRT54G on Win2
SP4.

mik

--
snowdog51
brought to you by http://www.wifi-forum.com

 
Reply With Quote
 
 
 
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
WRT54G link WPC54G without WPA.....!!!!!! Nicoco Wireless Internet 0 07-21-2005 12:14 PM
Linksys WRT54G and WPC54G network problems Cav Wireless Networks 4 10-31-2004 07:19 PM
Linksys WRT54G + WPC54G -- maximum range of 1 foot?! Mike Gnitecki Wireless Internet 7 01-30-2004 04:50 AM
Linksys WRT54G / WPC54G / IPAQ 5550 Peter Broadband 3 01-01-2004 03:58 PM
WRT54G/WPC54G -- Can the range be extended? Yves Thomas Wireless Internet 4 07-06-2003 08:21 PM



1 2 3 4 5 6 7 8 9 10 11