Not sure whether this is helpful, but I just had to figure out how to use the
bloody route update thing in CMAK, and the docs are poor, at best.
A couple of points that are missed in the docs:
1. The METRIC option is *not* optional. Failure to include it will result
in failed connections due to an 0x8007000B error (not documented). A
Microsoft poster on one forum incorrectly states that this is due to a
corrupted CMROUTE.DLL.
2. They should document the purpose of the REMOVE_GATEWAY command. See
below...
The basic approach that the routing table updates facility uses assumes that
the default gateway is set to the remote gateway. This allows the "default"
keywords to have some usefulness. But, using the remote gateway as the
default is often not desirable. So, REMOVE_GATEWAY allows the remote gateway
to be reset to its local default once the routes have been established on the
connection.
So, at least in my experience, the best option is to set things up with the
TCP/IP Settings / "Make this connection the client's default gateway"
(Gateway_On_Remote=1),
and use REMOVE_GATEWAY once the routes are established. The following
updates worked for me, for example:
ADD 10.70.40.0 MASK 255.255.255.0 default METRIC default IF default
ADD 10.70.42.0 MASK 255.255.255.0 default METRIC default IF default
REMOVE_GATEWAY
(Where my PPTP subnet is 10.70.41.0/24)
-- Bill
"Uche" wrote:
> I really need Expert help.
>
> I have setup a VPN server:
>
> OS 2003 standard member of domain SP2
> 2 nic card
> and 2 ip's
>
> If I manually connect to VPN server it works fine and do delete and adding
> of route everything is ok but if I use Connection Manager Administration Kit
> and which I have defined the route I will like to use and create the .exe
> file. Installing of the .exe file is ok but once it try to connect, it
> connects and disconnects with error
> “Connect action to update your routing table failed (80070057).� I looked
> at the VPN log, it say:
>
> ************************************************** ****************
> Operating System : Windows NT 5.1 Service Pack 2
> Dialer Version : 7.2.2600.2180
> Connection Name : test
> All Users/Single User : Single User
> Start Date/Time : 5/5/2006, 12:16:48
> ************************************************** ****************
> Module Name, Time, Log ID, Log Item Name, Other Info
> For Connection Type, 0=dial-up, 1=VPN, 2=VPN over dial-up
> ************************************************** ****************
> [cmdial32] 12:16:48 03 Pre-Init Event CallingProcess = C:\WINDOWS\Explorer.EXE
> [cmdial32] 12:17:04 04 Pre-Connect Event ConnectionType = 1
> [cmdial32] 12:17:04 06 Pre-Tunnel Event UserName = test Domain = vpn
> DUNSetting = test Tunnel DeviceName = TunnelAddress = 192.168.1.15
> [cmdial32] 12:17:05 07 Connect Event
> [cmdial32] 12:17:05 08 Custom Action Dll ActionType = Connect Actions
> Description = to update your routing table ActionPath = C:\Documents and
> Settings\tests\Application
> Data\Microsoft\Network\Connections\Cm\test\CMROUTE .DLL ReturnValue =
> 0x80070057
> [cmdial32] 12:17:05 20 On-Error Event ErrorCode = -2147024809 ErrorSource =
> to update your routing table
> [cmdial32] 12:17:05 12 Disconnect Event CallingProcess =
> C:\WINDOWS\system32\cmdial32.dll
> [cmdial32] 12:25:15 04 Pre-Connect Event ConnectionType = 1
> [cmdial32] 12:25:15 06 Pre-Tunnel Event UserName = test Domain = VPN
> DUNSetting = test Tunnel DeviceName = TunnelAddress = 192.168.1.15
> [cmdial32] 12:25:15 07 Connect Event
> [cmdial32] 12:25:15 08 Custom Action Dll ActionType = Connect Actions
> Description = to update your routing table ActionPath = C:\Documents and
> Settings\test\Application
> Data\Microsoft\Network\Connections\Cm\test\CMROUTE .DLL ReturnValue =
> 0x80070057
> [cmdial32] 12:25:15 20 On-Error Event ErrorCode = -2147024809 ErrorSource =
> to update your routing table
> [cmdial32] 12:25:15 12 Disconnect Event CallingProcess =
> C:\WINDOWS\system32\cmdial32.dll
>
>
> Please help
>
|
Similar Threads
Linear Mode
