WRT54G: DHCP plus static local IPs?

I'm trying to configure my WRT54G router (firmware v8.00.2, Jun. 7,
2007) with its DHCP server enabled, to allow friends and whatnot who
come over to be able to get internet access, but I also want to set
static IPs for a few machines that I own (so I can forward certain
ports).

I understand how to forward ports (using the Applications and Gaming
tab) but with DHCP enabled, if the power ever goes out, or a
connection gets lost for a while (laptop leaves coverage area and
stays out beyond DHCP lease time) then the machine may be reassigned a
new IP address.

I've used other routers where you can specify machines (by MAC
address) who get static IPs, while every other machine will get a
dynamic one issued through DHCP.

Is this possible with the stock firmware? Are there other firmwares
out there that I can replace it with that will do this for me?


Bo

Check and see if DD-WRT (www.dd-wrt.com) will load on a v8 router. If it
will than it will do what you want. other wise take the linksys back and buy
a buffalo.

Adair


"Bo" <(E-Mail Removed)> wrote in message
news:019226a6-143e-42e1-ac31-(E-Mail Removed)...
> I'm trying to configure my WRT54G router (firmware v8.00.2, Jun. 7,
> 2007) with its DHCP server enabled, to allow friends and whatnot who
> come over to be able to get internet access, but I also want to set
> static IPs for a few machines that I own (so I can forward certain
> ports).
>
> I understand how to forward ports (using the Applications and Gaming
> tab) but with DHCP enabled, if the power ever goes out, or a
> connection gets lost for a while (laptop leaves coverage area and
> stays out beyond DHCP lease time) then the machine may be reassigned a
> new IP address.
>
> I've used other routers where you can specify machines (by MAC
> address) who get static IPs, while every other machine will get a
> dynamic one issued through DHCP.
>
> Is this possible with the stock firmware? Are there other firmwares
> out there that I can replace it with that will do this for me?

Thanks. I guess I just couldn't find information about dd-wrt or
openwrt just by googling "static dhcp". I'll try out these 3rd party
firmwares and see what works best.

On Nov 15, 6:39 pm, "Adair Winter" <ada...@swbell.net> wrote:
> Check and see if DD-WRT (www.dd-wrt.com) will load on a v8 router. If it
> will than it will do what you want. other wise take the linksys back and buy
> a buffalo.
>
> Adair
>
> "Bo" <boboudr...@gmail.com> wrote in message
>
> news:019226a6-143e-42e1-ac31-(E-Mail Removed)...
>
> > I'm trying to configure my WRT54G router (firmware v8.00.2, Jun. 7,
> > 2007) with its DHCP server enabled, to allow friends and whatnot who
> > come over to be able to get internet access, but I also want to set
> > static IPs for a few machines that I own (so I can forward certain
> > ports).
>
> > I understand how to forward ports (using the Applications and Gaming
> > tab) but with DHCP enabled, if the power ever goes out, or a
> > connection gets lost for a while (laptop leaves coverage area and
> > stays out beyond DHCP lease time) then the machine may be reassigned a
> > new IP address.
>
> > I've used other routers where you can specify machines (by MAC
> > address) who get static IPs, while every other machine will get a
> > dynamic one issued through DHCP.
>
> > Is this possible with the stock firmware? Are there other firmwares
> > out there that I can replace it with that will do this for me?

Just setup your internal machines with static addresses. Then make sure the
internal DHCP leases are from a different chunk of that same internal
subnet. Your forwarded ports go to your internal machines, which will
always be on the same addresses due to them being setup manually with static
ones.


"Bo" <(E-Mail Removed)> wrote in message
news:019226a6-143e-42e1-ac31-(E-Mail Removed)...
> I'm trying to configure my WRT54G router (firmware v8.00.2, Jun. 7,
> 2007) with its DHCP server enabled, to allow friends and whatnot who
> come over to be able to get internet access, but I also want to set
> static IPs for a few machines that I own (so I can forward certain
> ports).
>
> I understand how to forward ports (using the Applications and Gaming
> tab) but with DHCP enabled, if the power ever goes out, or a
> connection gets lost for a while (laptop leaves coverage area and
> stays out beyond DHCP lease time) then the machine may be reassigned a
> new IP address.
>
> I've used other routers where you can specify machines (by MAC
> address) who get static IPs, while every other machine will get a
> dynamic one issued through DHCP.
>
> Is this possible with the stock firmware? Are there other firmwares
> out there that I can replace it with that will do this for me?

I have the WRT54G Router and I have used if for the same things that you
are trying to do and I had no problems.
I left my router on dhcp enabled and I have never had any of my
computers that where setup with static ip addresses to have then go to
dhcp after the connection got lost or the power went out.
this what I did to set it up I left dhcp enabled and then I just set up
my computers for static ip addresses and then you also have to enter in
the dns server addresses in order for it to work so just call your isp
for the dns server addresses or if you can find your isp in this link
then just use those from that site
http://portforward.com/networking/dns.htm you do not need to do this in
some linux distros cause I have set up a static ip address on one of my
linux systems and it automatically found out what the dns was and the
wired thing was those dns servers for my isp which is comcast where not
listed at that site.

I have the WRT54G Router and I have used if for the same things that you
are trying to do and I had no problems.
I left my router on dhcp enabled and I have never had any of my
computers that where setup with static ip addresses to have then go to
dhcp after the connection got lost or the power went out.
this what I did to set it up I left dhcp enabled and then I just set up
my computers for static ip addresses and then you also have to enter in
the dns server addresses in order for it to work so just call your isp
for the dns server addresses or if you can find your isp in this link
then just use the dns server addresses from that site
http://portforward.com/networking/dns.htm you do not need to do this in
some linux distros cause I have set up a static ip address on one of my
linux systems and it automatically found out what the dns was and the
wired thing was those dns servers for my isp which is comcast where not
listed at that site. if you do not know how to set up a static ip
address on your computer go to this link
http://www.portforward.com/networking/staticip.htm
if you need help setting up forwarding ports then go to this link
http://www.portforward.com/english/r...RT54Gindex.htm