CAT-5 cable stuck in ethernet port - can't remove

I just bought a brand-new laptop (Thinpad R52) and connected a CAT-5
cable into the Ethernet port. It seemed a bit tight at first when
inserting the cable, but after a bit of pressure, I felt the cable snap
in to place. Everything worked fine until I tried to remove the cable.
Pressing down on the clip of the RJ45 connector results in a very
quiet snapping sound, but the cable is still stuck hard in place.

I've tried multiple angles, nudging it in deeper and then trying to
remove it, pressing down both soft and hard on the clip, but the cable
is still stuck in the port. This problem is pretty frustrating - in
years of using networking gear I've never seen a cable stuck like this
before. Any tips to removing that cable - without damaging the
Ethernet port - would be greatfully welcomed.

patiwat_at_sloan.mit.edu



patiwatp@gmail.com

(E-Mail Removed) schreef:
> I just bought a brand-new laptop (Thinpad R52) and connected a CAT-5
> cable into the Ethernet port. It seemed a bit tight at first when
> inserting the cable, but after a bit of pressure, I felt the cable snap
> in to place. Everything worked fine until I tried to remove the cable.
> Pressing down on the clip of the RJ45 connector results in a very
> quiet snapping sound, but the cable is still stuck hard in place.
>
> I've tried multiple angles, nudging it in deeper and then trying to
> remove it, pressing down both soft and hard on the clip, but the cable
> is still stuck in the port. This problem is pretty frustrating - in
> years of using networking gear I've never seen a cable stuck like this
> before. Any tips to removing that cable - without damaging the
> Ethernet port - would be greatfully welcomed.
>
> patiwat_at_sloan.mit.edu
>

You could try to use a small screwdriver (like they use for repairing
watches). Stick it where the clip used to be and put some light presure
on it (make the tip tilt slightly upwards) while gently pulling the RJ-45.

Good luck

On 26 Apr 2006 02:41:48 -0700, (E-Mail Removed) wrote:


I would assume that the RJ 45 connector was not properly crimped what
resulted in jamming at the port.
After you have broken the clip, which holds the connector in place,
there is no need to try and hold this clip down. It's gone!
Fallow the tip from the previous poster by gently rocking the RJ 45
out of the port but I would apply a little spray of WD40 or similar.

Good luck!
Regards
Helmut


>
>I just bought a brand-new laptop (Thinpad R52) and connected a CAT-5
>cable into the Ethernet port. It seemed a bit tight at first when
>inserting the cable, but after a bit of pressure, I felt the cable snap
>in to place. Everything worked fine until I tried to remove the cable.
> Pressing down on the clip of the RJ45 connector results in a very
>quiet snapping sound, but the cable is still stuck hard in place.
>
>I've tried multiple angles, nudging it in deeper and then trying to
>remove it, pressing down both soft and hard on the clip, but the cable
>is still stuck in the port. This problem is pretty frustrating - in
>years of using networking gear I've never seen a cable stuck like this
>before. Any tips to removing that cable - without damaging the
>Ethernet port - would be greatfully welcomed.
>
>patiwat_at_sloan.mit.edu

<(E-Mail Removed)> wrote in message
news:(E-Mail Removed) oups.com
> I just bought a brand-new laptop (Thinpad R52) and connected a
> CAT-5
> cable into the Ethernet port. It seemed a bit tight at first
> when
> inserting the cable, but after a bit of pressure, I felt the
> cable
> snap in to place. Everything worked fine until I tried to
> remove
> the cable. Pressing down on the clip of the RJ45 connector
> results
> in a very quiet snapping sound, but the cable is still stuck
> hard
> in place.
>
> I've tried multiple angles, nudging it in deeper and then
> trying to
> remove it, pressing down both soft and hard on the clip, but
> the
> cable is still stuck in the port. This problem is pretty
> frustrating - in years of using networking gear I've never seen
> a
> cable stuck like this before. Any tips to removing that
> cable -
> without damaging the Ethernet port - would be greatfully
> welcomed.
>
> patiwat_at_sloan.mit.edu

If you just purchased it the warranty should still apply. Take
it back to the seller.

--


Travis in Shoreline Washington

Did you try needle-nose pliers to squeeze the clip and grab the connector at
the same time?


"Travis M." <(E-Mail Removed)> wrote in message
news:Tr64g.1355$Te.1253@trndny04...
> <(E-Mail Removed)> wrote in message
> news:(E-Mail Removed) oups.com
>> I just bought a brand-new laptop (Thinpad R52) and connected a CAT-5
>> cable into the Ethernet port. It seemed a bit tight at first when
>> inserting the cable, but after a bit of pressure, I felt the cable
>> snap in to place. Everything worked fine until I tried to remove
>> the cable. Pressing down on the clip of the RJ45 connector results
>> in a very quiet snapping sound, but the cable is still stuck hard
>> in place.
>>
>> I've tried multiple angles, nudging it in deeper and then trying to
>> remove it, pressing down both soft and hard on the clip, but the
>> cable is still stuck in the port. This problem is pretty
>> frustrating - in years of using networking gear I've never seen a
>> cable stuck like this before. Any tips to removing that cable -
>> without damaging the Ethernet port - would be greatfully welcomed.
>>
>> patiwat_at_sloan.mit.edu
>
> If you just purchased it the warranty should still apply. Take it back to
> the seller.
>
> --
>
>
> Travis in Shoreline Washington

patiwat(p):

A "trick" used in similar cases in the service sector is to get a can
of "freeze spray" sold in some specialized electronics parts stores.
When the freeze spray hits the connector, it should contract
ever-so-slightly but probably enough to allow an extraction. That
amazingly used to get you out of jam in some cases.

I'd stay away from the WD-40 though...you'll be setting yourself up
for intermittant connections later on. The petroleum products are
probably harsh in comparison to the 'old' tuner-cleaner or better
known now as "contact cleaner" solutions.

Zeng

On Thu, 27 Apr 2006 10:58:19 +1000, hstamm <(E-Mail Removed)>
wrote:

>On 26 Apr 2006 02:41:48 -0700, (E-Mail Removed) wrote:
>
>
>I would assume that the RJ 45 connector was not properly crimped what
>resulted in jamming at the port.
>After you have broken the clip, which holds the connector in place,
>there is no need to try and hold this clip down. It's gone!
>Fallow the tip from the previous poster by gently rocking the RJ 45
>out of the port but I would apply a little spray of WD40 or similar.
>
>Good luck!
>Regards
>Helmut
>
>
>>
>>I just bought a brand-new laptop (Thinpad R52) and connected a CAT-5
>>cable into the Ethernet port. It seemed a bit tight at first when
>>inserting the cable, but after a bit of pressure, I felt the cable snap
>>in to place. Everything worked fine until I tried to remove the cable.
>> Pressing down on the clip of the RJ45 connector results in a very
>>quiet snapping sound, but the cable is still stuck hard in place.
>>
>>I've tried multiple angles, nudging it in deeper and then trying to
>>remove it, pressing down both soft and hard on the clip, but the cable
>>is still stuck in the port. This problem is pretty frustrating - in
>>years of using networking gear I've never seen a cable stuck like this
>>before. Any tips to removing that cable - without damaging the
>>Ethernet port - would be greatfully welcomed.
>>
>>patiwat_at_sloan.mit.edu

<(E-Mail Removed)> wrote in message
news:(E-Mail Removed) oups.com...
>
> I just bought a brand-new laptop (Thinpad R52) and connected a CAT-5
> cable into the Ethernet port. It seemed a bit tight at first when
> inserting the cable, but after a bit of pressure, I felt the cable snap
> in to place. Everything worked fine until I tried to remove the cable.
> Pressing down on the clip of the RJ45 connector results in a very
> quiet snapping sound, but the cable is still stuck hard in place.
>
> I've tried multiple angles, nudging it in deeper and then trying to
> remove it, pressing down both soft and hard on the clip, but the cable
> is still stuck in the port. This problem is pretty frustrating - in
> years of using networking gear I've never seen a cable stuck like this
> before. Any tips to removing that cable - without damaging the
> Ethernet port - would be greatfully welcomed.
>
> patiwat_at_sloan.mit.edu
>

You're at MIT: take it over to the IT department and have them get the thing
out.