Compatibility? MS-500 Base/DLink520 pci adapter

Could use some help...have Microsoft 500
router..installed DLink 520 adapter on upstairs
desktop...DLink card is functioning..however will not
connect to MS router..what do I need to change to connect
the two? Thanks!


Jeebs

You can't use the proprietary speed modes on any of the DLink or other
vendors NICs to connect to the standards based MN-500.



On Sat, 7 Feb 2004 19:09:53 -0800, "Jeebs"
<(E-Mail Removed)> wrote:

>Could use some help...have Microsoft 500
>router..installed DLink 520 adapter on upstairs
>desktop...DLink card is functioning..however will not
>connect to MS router..what do I need to change to connect
>the two? Thanks!

--
Barb Bowman
Expert Zone Columnist
http://www.microsoft.com/windowsxp/expertzone
MS-MVP (Windows)

Barb,
Thanks for getting back to me...as a follow up..(and
please understand this is new territory for me)does you
response mean that the DLink and MS500 function together?
I was assured @ Office Depot that they would...however if
not I have no problem returning the DLink and purchasing
anothe MS pci card...Thanks again! Jeff
>-----Original Message-----
>You can't use the proprietary speed modes on any of the
DLink or other
>vendors NICs to connect to the standards based MN-500.
>
>
>
>On Sat, 7 Feb 2004 19:09:53 -0800, "Jeebs"
><(E-Mail Removed)> wrote:
>
>>Could use some help...have Microsoft 500
>>router..installed DLink 520 adapter on upstairs
>>desktop...DLink card is functioning..however will not
>>connect to MS router..what do I need to change to
connect
>>the two? Thanks!
>
>--
>Barb Bowman
>Expert Zone Columnist
>http://www.microsoft.com/windowsxp/expertzone
>MS-MVP (Windows)
>.
>

They should work together fine as long as you don't try to use the
special speed enhancement modes that some of these adapters offer.
DLink has a version of the 520 that is advertised to do 22mbps. But
you can't use that mode with the MN500.

On Sun, 8 Feb 2004 10:37:15 -0800, "Jeebs"
<(E-Mail Removed)> wrote:

>Barb,
> Thanks for getting back to me...as a follow up..(and
>please understand this is new territory for me)does you
>response mean that the DLink and MS500 function together?
>I was assured @ Office Depot that they would...however if
>not I have no problem returning the DLink and purchasing
>anothe MS pci card...Thanks again! Jeff
>>-----Original Message-----
>>You can't use the proprietary speed modes on any of the
>DLink or other
>>vendors NICs to connect to the standards based MN-500.
>>
>>
>>
>>On Sat, 7 Feb 2004 19:09:53 -0800, "Jeebs"
>><(E-Mail Removed)> wrote:
>>
>>>Could use some help...have Microsoft 500
>>>router..installed DLink 520 adapter on upstairs
>>>desktop...DLink card is functioning..however will not
>>>connect to MS router..what do I need to change to
>connect
>>>the two? Thanks!
>>
>>--
>>Barb Bowman
>>Expert Zone Columnist
>>http://www.microsoft.com/windowsxp/expertzone
>>MS-MVP (Windows)
>>.
>>

--
Barb Bowman
Expert Zone Columnist
http://www.microsoft.com/windowsxp/expertzone
MS-MVP (Windows)

Hi agin Barb....I was on the phone with DLink last
evening..they had me do some things to check out there
card..it was functional..however I could not get a
connection to the MN 500..they told me that based on the
INS address( I believe the first three #'s were 167.)that
told them the MN500 does not "see" the DLink...what do I
need to do to get connected?? By the way..this DLink is
11mbps...Are there addresses that shouls match up between
router and card adapter?? (Can u tell I'm a rookie?)


>-----Original Message-----
>They should work together fine as long as you don't try
to use the
>special speed enhancement modes that some of these
adapters offer.
>DLink has a version of the 520 that is advertised to do
22mbps. But
>you can't use that mode with the MN500.
>
>On Sun, 8 Feb 2004 10:37:15 -0800, "Jeebs"
><(E-Mail Removed)> wrote:
>
>>Barb,
>> Thanks for getting back to me...as a follow up..(and
>>please understand this is new territory for me)does you
>>response mean that the DLink and MS500 function
together?
>>I was assured @ Office Depot that they would...however
if
>>not I have no problem returning the DLink and
purchasing
>>anothe MS pci card...Thanks again! Jeff
>>>-----Original Message-----
>>>You can't use the proprietary speed modes on any of
the
>>DLink or other
>>>vendors NICs to connect to the standards based MN-500.
>>>
>>>
>>>
>>>On Sat, 7 Feb 2004 19:09:53 -0800, "Jeebs"
>>><(E-Mail Removed)> wrote:
>>>
>>>>Could use some help...have Microsoft 500
>>>>router..installed DLink 520 adapter on upstairs
>>>>desktop...DLink card is functioning..however will not
>>>>connect to MS router..what do I need to change to
>>connect
>>>>the two? Thanks!
>>>
>>>--
>>>Barb Bowman
>>>Expert Zone Columnist
>>>http://www.microsoft.com/windowsxp/expertzone
>>>MS-MVP (Windows)
>>>.
>>>
>
>--
>Barb Bowman
>Expert Zone Columnist
>http://www.microsoft.com/windowsxp/expertzone
>MS-MVP (Windows)
>.
>

What operating system are you using? Make sure the DLink adapter is in
Infrastructure and not ad hoc mode and that it has the correct SSID
configured and not "default". Make sure you are using 128 bit WEP in
both devices (and use a HEX key in the DLink). You probably can get
more help configuring the DLink card at
http://www.dslreports.com/forum/dlink

On Sun, 8 Feb 2004 12:30:05 -0800, "Jeebs"
<(E-Mail Removed)> wrote:

>Hi agin Barb....I was on the phone with DLink last
>evening..they had me do some things to check out there
>card..it was functional..however I could not get a
>connection to the MN 500..they told me that based on the
>INS address( I believe the first three #'s were 167.)that
>told them the MN500 does not "see" the DLink...what do I
>need to do to get connected?? By the way..this DLink is
>11mbps...Are there addresses that shouls match up between
>router and card adapter?? (Can u tell I'm a rookie?)
>
>
>>-----Original Message-----
>>They should work together fine as long as you don't try
>to use the
>>special speed enhancement modes that some of these
>adapters offer.
>>DLink has a version of the 520 that is advertised to do
>22mbps. But
>>you can't use that mode with the MN500.
>>
>>On Sun, 8 Feb 2004 10:37:15 -0800, "Jeebs"
>><(E-Mail Removed)> wrote:
>>
>>>Barb,
>>> Thanks for getting back to me...as a follow up..(and
>>>please understand this is new territory for me)does you
>>>response mean that the DLink and MS500 function
>together?
>>>I was assured @ Office Depot that they would...however
>if
>>>not I have no problem returning the DLink and
>purchasing
>>>anothe MS pci card...Thanks again! Jeff
>>>>-----Original Message-----
>>>>You can't use the proprietary speed modes on any of
>the
>>>DLink or other
>>>>vendors NICs to connect to the standards based MN-500.
>>>>
>>>>
>>>>
>>>>On Sat, 7 Feb 2004 19:09:53 -0800, "Jeebs"
>>>><(E-Mail Removed)> wrote:
>>>>
>>>>>Could use some help...have Microsoft 500
>>>>>router..installed DLink 520 adapter on upstairs
>>>>>desktop...DLink card is functioning..however will not
>>>>>connect to MS router..what do I need to change to
>>>connect
>>>>>the two? Thanks!
>>>>
>>>>--
>>>>Barb Bowman
>>>>Expert Zone Columnist
>>>>http://www.microsoft.com/windowsxp/expertzone
>>>>MS-MVP (Windows)
>>>>.
>>>>
>>
>>--
>>Barb Bowman
>>Expert Zone Columnist
>>http://www.microsoft.com/windowsxp/expertzone
>>MS-MVP (Windows)
>>.
>>

--
Barb Bowman
Expert Zone Columnist
http://www.microsoft.com/windowsxp/expertzone
MS-MVP (Windows)

Barb..using Win'98 on the DLink desktop..MN-500 has Win
XP....should encryption be enabled??Where will I check
for 128 bit WEP? Thanks SO much for your help! Jeff

>-----Original Message-----
>What operating system are you using? Make sure the DLink
adapter is in
>Infrastructure and not ad hoc mode and that it has the
correct SSID
>configured and not "default". Make sure you are using
128 bit WEP in
>both devices (and use a HEX key in the DLink). You
probably can get
>more help configuring the DLink card at
>http://www.dslreports.com/forum/dlink
>
>On Sun, 8 Feb 2004 12:30:05 -0800, "Jeebs"
><(E-Mail Removed)> wrote:
>
>>Hi agin Barb....I was on the phone with DLink last
>>evening..they had me do some things to check out there
>>card..it was functional..however I could not get a
>>connection to the MN 500..they told me that based on
the
>>INS address( I believe the first three #'s were 167.)
that
>>told them the MN500 does not "see" the DLink...what do
I
>>need to do to get connected?? By the way..this DLink is
>>11mbps...Are there addresses that shouls match up
between
>>router and card adapter?? (Can u tell I'm a rookie?)
>>
>>
>>>-----Original Message-----
>>>They should work together fine as long as you don't
try
>>to use the
>>>special speed enhancement modes that some of these
>>adapters offer.
>>>DLink has a version of the 520 that is advertised to
do
>>22mbps. But
>>>you can't use that mode with the MN500.
>>>
>>>On Sun, 8 Feb 2004 10:37:15 -0800, "Jeebs"
>>><(E-Mail Removed)> wrote:
>>>
>>>>Barb,
>>>> Thanks for getting back to me...as a follow up..(and
>>>>please understand this is new territory for me)does
you
>>>>response mean that the DLink and MS500 function
>>together?
>>>>I was assured @ Office Depot that they
would...however
>>if
>>>>not I have no problem returning the DLink and
>>purchasing
>>>>anothe MS pci card...Thanks again! Jeff
>>>>>-----Original Message-----
>>>>>You can't use the proprietary speed modes on any of
>>the
>>>>DLink or other
>>>>>vendors NICs to connect to the standards based MN-
500.
>>>>>
>>>>>
>>>>>
>>>>>On Sat, 7 Feb 2004 19:09:53 -0800, "Jeebs"
>>>>><(E-Mail Removed)> wrote:
>>>>>
>>>>>>Could use some help...have Microsoft 500
>>>>>>router..installed DLink 520 adapter on upstairs
>>>>>>desktop...DLink card is functioning..however will
not
>>>>>>connect to MS router..what do I need to change to
>>>>connect
>>>>>>the two? Thanks!
>>>>>
>>>>>--
>>>>>Barb Bowman
>>>>>Expert Zone Columnist
>>>>>http://www.microsoft.com/windowsxp/expertzone
>>>>>MS-MVP (Windows)
>>>>>.
>>>>>
>>>
>>>--
>>>Barb Bowman
>>>Expert Zone Columnist
>>>http://www.microsoft.com/windowsxp/expertzone
>>>MS-MVP (Windows)
>>>.
>>>
>
>--
>Barb Bowman
>Expert Zone Columnist
>http://www.microsoft.com/windowsxp/expertzone
>MS-MVP (Windows)
>.
>

the setup wizard from the MN-500 should have allowed you to enable 128
bit WEP encryption. Either rerun the wizard OR manually access the
base station. I'd suggest in your case using the wizard.

You will need to refer to DLink support for help with configuring WEP
with their wireless adapter. We can't help you here with your DLink
card.

On Sun, 8 Feb 2004 13:35:14 -0800, "Jeebs"
<(E-Mail Removed)> wrote:

>Barb..using Win'98 on the DLink desktop..MN-500 has Win
>XP....should encryption be enabled??Where will I check
>for 128 bit WEP? Thanks SO much for your help! Jeff
>
>>-----Original Message-----
>>What operating system are you using? Make sure the DLink
>adapter is in
>>Infrastructure and not ad hoc mode and that it has the
>correct SSID
>>configured and not "default". Make sure you are using
>128 bit WEP in
>>both devices (and use a HEX key in the DLink). You
>probably can get
>>more help configuring the DLink card at
>>http://www.dslreports.com/forum/dlink
>>
>>On Sun, 8 Feb 2004 12:30:05 -0800, "Jeebs"
>><(E-Mail Removed)> wrote:
>>
>>>Hi agin Barb....I was on the phone with DLink last
>>>evening..they had me do some things to check out there
>>>card..it was functional..however I could not get a
>>>connection to the MN 500..they told me that based on
>the
>>>INS address( I believe the first three #'s were 167.)
>that
>>>told them the MN500 does not "see" the DLink...what do
>I
>>>need to do to get connected?? By the way..this DLink is
>>>11mbps...Are there addresses that shouls match up
>between
>>>router and card adapter?? (Can u tell I'm a rookie?)
>>>
>>>
>>>>-----Original Message-----
>>>>They should work together fine as long as you don't
>try
>>>to use the
>>>>special speed enhancement modes that some of these
>>>adapters offer.
>>>>DLink has a version of the 520 that is advertised to
>do
>>>22mbps. But
>>>>you can't use that mode with the MN500.
>>>>
>>>>On Sun, 8 Feb 2004 10:37:15 -0800, "Jeebs"
>>>><(E-Mail Removed)> wrote:
>>>>
>>>>>Barb,
>>>>> Thanks for getting back to me...as a follow up..(and
>>>>>please understand this is new territory for me)does
>you
>>>>>response mean that the DLink and MS500 function
>>>together?
>>>>>I was assured @ Office Depot that they
>would...however
>>>if
>>>>>not I have no problem returning the DLink and
>>>purchasing
>>>>>anothe MS pci card...Thanks again! Jeff
>>>>>>-----Original Message-----
>>>>>>You can't use the proprietary speed modes on any of
>>>the
>>>>>DLink or other
>>>>>>vendors NICs to connect to the standards based MN-
>500.
>>>>>>
>>>>>>
>>>>>>
>>>>>>On Sat, 7 Feb 2004 19:09:53 -0800, "Jeebs"
>>>>>><(E-Mail Removed)> wrote:
>>>>>>
>>>>>>>Could use some help...have Microsoft 500
>>>>>>>router..installed DLink 520 adapter on upstairs
>>>>>>>desktop...DLink card is functioning..however will
>not
>>>>>>>connect to MS router..what do I need to change to
>>>>>connect
>>>>>>>the two? Thanks!
>>>>>>
>>>>>>--
>>>>>>Barb Bowman
>>>>>>Expert Zone Columnist
>>>>>>http://www.microsoft.com/windowsxp/expertzone
>>>>>>MS-MVP (Windows)
>>>>>>.
>>>>>>
>>>>
>>>>--
>>>>Barb Bowman
>>>>Expert Zone Columnist
>>>>http://www.microsoft.com/windowsxp/expertzone
>>>>MS-MVP (Windows)
>>>>.
>>>>
>>
>>--
>>Barb Bowman
>>Expert Zone Columnist
>>http://www.microsoft.com/windowsxp/expertzone
>>MS-MVP (Windows)
>>.
>>

--
Barb Bowman
Expert Zone Columnist
http://www.microsoft.com/windowsxp/expertzone
MS-MVP (Windows)