Networking Forums

Networking Forums > Computer Networking > Broadband > Modem router for Plusnet / Force 9

Reply
Thread Tools Display Modes

Modem router for Plusnet / Force 9

 
 
Brian A
Guest
Posts: n/a

 
      02-08-2005, 12:01 PM
1. I use Netgear combination DM602 / WGR614 on Force 9 and all works
well.
I am looking at another installation on Force 9 and would prefer to
use Netgear because I am used to it. How well does the Netgear 'all in
one box' DG834GT work with Force 9? - or any other recommendations.
I had to set up the DM602 modem/router as a router on my set-up to
makethe combination work with PPPoA so I am a bit concerned as to how
well the DG834GT might operate.

2. Anyone used the gear sold by F9? What make is it?

3. Has anyone used any of the above on Sipgate?
(perhaps more a question for the Telecoms Newsgroup)
Remove 'no_spam_' from email address.
 
Reply With Quote
 
 
 
 
cw
Guest
Posts: n/a

 
      02-08-2005, 07:52 PM
The DSLAM termination equipment is the same regardless of the ISP so you
don't need to ask about particular ISPs. Personally I hate Netgear stuff.
We have had a few problematic Netgear ADSL boxes at customer premises and
on a different level their VPN boxes are absolutely atrocious (or rather
the software is so badly designed and difficult to configure.

At home I have had an Asus, Dynamode (which died and got taken back) and
a Westell. Beware of *anything* based on the Conexant chipset (ie the
Dynamode). MRI don't seem to fare too well, we mostly use Cisco boxes for
businesses and their sister company's boxes for home use (Linksys)

--
Colin
*Drop DEAD from the email address to reply*
 
Reply With Quote
 
Martin²
Guest
Posts: n/a

 
      02-09-2005, 12:33 AM
Brian A:
>3. Has anyone used any of the above on Sipgate?


Sipgate works just fine on PlusNet, and should on any 'decent' broadband
(i.e. preferably 512Mb/s ).
If you are into VoIP you should consider routers with VoIP phone sockets so
you can make VoIP calls without the computer
being switched on. Check out the Zoom X5V if you want a cheap one,
Draytek Vigor 2500V for very good one, and Vigor 2600V (two VoIP sockets) if
you want the best.
Regards,
Martin


 
Reply With Quote
 
Brian A
Guest
Posts: n/a

 
      02-09-2005, 12:19 PM
On Wed, 9 Feb 2005 01:33:05 -0000, "Martin²" <(E-Mail Removed)> wrote:

>Brian A:
>>3. Has anyone used any of the above on Sipgate?

>
>Sipgate works just fine on PlusNet, and should on any 'decent' broadband
>(i.e. preferably 512Mb/s ).
>If you are into VoIP you should consider routers with VoIP phone sockets so
>you can make VoIP calls without the computer

I thought the Sipgate router would plug into standard RJ45 router
sockets and then operate with the computer off.
Just what are VoIP sockets?

Remove 'no_spam_' from email address.
 
Reply With Quote
 
Martin²
Guest
Posts: n/a

 
      02-10-2005, 12:41 AM
Brian A:
>I thought the Sipgate router would plug into standard RJ45 router
>sockets and then operate with the computer off.
>Just what are VoIP sockets?


You can have an ATA adaptor / router plugged to your ethernet RJ45,
then plug ordinary analog phone into that using RJ11 plug.
Or you can buy IP phone which plugs directly into the RJ45.
Either will cost you £69 + p&p from sipgate.

Routers with VoIP socket(s) have the adaptor built in, so you get one or two
RJ11 sockets to plug your ordinary (cordless)
phone(s) into, in addition to (normally) 4 ethernet RJ45 ports.
In addition (at least with Draytek) the VoIP phone can also use the POTS
line, it also defaults to it in case of power failure.
Regards,
Martin


 
Reply With Quote
 
Brian A
Guest
Posts: n/a

 
      02-11-2005, 11:13 AM
On Thu, 10 Feb 2005 01:41:37 -0000, "Martin²" <(E-Mail Removed)> wrote:

>Brian A:
>>I thought the Sipgate router would plug into standard RJ45 router
>>sockets and then operate with the computer off.
>>Just what are VoIP sockets?

>
>You can have an ATA adaptor / router plugged to your ethernet RJ45,
>then plug ordinary analog phone into that using RJ11 plug.
>Or you can buy IP phone which plugs directly into the RJ45.
>Either will cost you £69 + p&p from sipgate.
>
>Routers with VoIP socket(s) have the adaptor built in, so you get one or two
>RJ11 sockets to plug your ordinary (cordless)
>phone(s) into, in addition to (normally) 4 ethernet RJ45 ports.
>In addition (at least with Draytek) the VoIP phone can also use the POTS
>line, it also defaults to it in case of power failure.
>Regards,
>Martin
>

Thanks for this information. I will probably go for the Draytec and
use it on F9/Plusnet.
What is the customer service like on Draytec if you get a problem with
set up?
Remove 'no_spam_' from email address.
 
Reply With Quote
 
Martin²
Guest
Posts: n/a

 
      02-12-2005, 12:40 AM
Brian A:
>What is the customer service like on Draytec if you get a problem with
>set up?


www.seg.co.uk provide Draytek UK support and have a forum, useful for
advanced setup.
I gather that they are helpful, never had need to use them, except to
download upgraded firmware
to make the VoIP work (my Vigor 2600 is two years old).
Regards,
Martin


 
Reply With Quote
 
 
 
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Nike Air Force Ones,Air Force One Air Force One-1,25th anniversary lky52136@gmail.com Windows Networking 0 01-14-2008 07:45 PM
Swap required: 3-Com ADSL wireless modem/router for wirelesss router without modem Adam Lipscombe Home Networking 2 04-30-2006 12:05 PM
Which ISP Wanadoo or Plusnet or ANother ? Modem or Router ? Ronald Jones Broadband 3 09-13-2004 08:49 PM
PLusnet Modem Query pgiblin Broadband 8 08-18-2004 04:37 PM
Plusnet and Modem Chris S Broadband 9 05-12-2004 12:03 PM



1 2 3 4 5 6 7 8 9 10 11