MN-500 can not configure

I can ping the 192.168.2.1 but when I try to connect all I
get is page can not be displayed.
When I reboot my computer, the ISP locks me out and I have
to remove the MN-500 and reboot the computer again.

Any ideas?

You may be probably in bridge mode -- in bridge mode the
router cannot be accessed through Ports 1-4. Reset the
router using the reset hole on the back, wait while the
power light is orange and/or blinks. All router settings
will be lost, and password reverts to admin

>-----Original Message-----
>I can ping the 192.168.2.1 but when I try to connect all
I
>get is page can not be displayed.
>When I reboot my computer, the ISP locks me out and I
have
>to remove the MN-500 and reboot the computer again.
>
>Any ideas?
>.
>

I have tried reseting the unit. I can still only ping
it. Would this mean the unit is defective? I am not
running any kind of firewall software, and disabled the
anti-virus before the install.

>-----Original Message-----
>You may be probably in bridge mode -- in bridge mode the
>router cannot be accessed through Ports 1-4. Reset the
>router using the reset hole on the back, wait while the
>power light is orange and/or blinks. All router settings
>will be lost, and password reverts to admin
>
>>-----Original Message-----
>>I can ping the 192.168.2.1 but when I try to connect all
>I
>>get is page can not be displayed.
>>When I reboot my computer, the ISP locks me out and I
>have
>>to remove the MN-500 and reboot the computer again.
>>
>>Any ideas?
>>.
>>
>.
>

Did you hold the reset button for more than 7 seconds? Such that the power
light flashed yellow?

--
Jason Tsang - Microsoft MVP

Find out about the MS MVP Program -
http://mvp.support.microsoft.com/default.aspx

"yoda_plushy" <(E-Mail Removed)> wrote in message
news:1b4f901c42090$dbee8d40$(E-Mail Removed)...
> I have tried reseting the unit. I can still only ping
> it. Would this mean the unit is defective? I am not
> running any kind of firewall software, and disabled the
> anti-virus before the install.
>
> >-----Original Message-----
> >You may be probably in bridge mode -- in bridge mode the
> >router cannot be accessed through Ports 1-4. Reset the
> >router using the reset hole on the back, wait while the
> >power light is orange and/or blinks. All router settings
> >will be lost, and password reverts to admin
> >
> >>-----Original Message-----
> >>I can ping the 192.168.2.1 but when I try to connect all
> >I
> >>get is page can not be displayed.
> >>When I reboot my computer, the ISP locks me out and I
> >have
> >>to remove the MN-500 and reboot the computer again.
> >>
> >>Any ideas?
> >>.
> >>
> >.
> >

Seven Seconds, no... so the power light turns yellow and
flashes yes.

>-----Original Message-----
>Did you hold the reset button for more than 7 seconds?
Such that the power
>light flashed yellow?
>
>--
>Jason Tsang - Microsoft MVP
>
>Find out about the MS MVP Program -
>http://mvp.support.microsoft.com/default.aspx
>
>"yoda_plushy" <(E-Mail Removed)> wrote
in message
>news:1b4f901c42090$dbee8d40$(E-Mail Removed)...
>> I have tried reseting the unit. I can still only ping
>> it. Would this mean the unit is defective? I am not
>> running any kind of firewall software, and disabled the
>> anti-virus before the install.
>>
>> >-----Original Message-----
>> >You may be probably in bridge mode -- in bridge mode
the
>> >router cannot be accessed through Ports 1-4. Reset the
>> >router using the reset hole on the back, wait while the
>> >power light is orange and/or blinks. All router
settings
>> >will be lost, and password reverts to admin
>> >
>> >>-----Original Message-----
>> >>I can ping the 192.168.2.1 but when I try to connect
all
>> >I
>> >>get is page can not be displayed.
>> >>When I reboot my computer, the ISP locks me out and I
>> >have
>> >>to remove the MN-500 and reboot the computer again.
>> >>
>> >>Any ideas?
>> >>.
>> >>
>> >.
>> >
>
>
>.
>

I have tried twice holding the reset button in for over 10
seconds each time. The power light changes to yellow and
the lights all flash, but I am still unable to configure
the unit. I can ping, and I can connect to the internet
through the unit until I reboot.



>-----Original Message-----
>Did you hold the reset button for more than 7 seconds?
Such that the power
>light flashed yellow?
>
>--
>Jason Tsang - Microsoft MVP
>