Linksys WRT54G computer doesn't see router

My Linksys WRT54G v. 3.0 has a blinking power light. I read on Linksys'
site that I should update the firmware. Unfortunately, my computer
isn't even seeing the router.

My modem is connected to the router, and my computer is connected
through one of the router's ports, but when I ping 192.168.1.1 I'm
getting a time out.

All my computer can see is the modem. It's like I'm not even connected
to the router.

Any ideas on how I can fix this? Thanks for any and all help.


------------------------------------------------------------------------
View this thread: http://www.wirelessforums.org/showthread.php?t=34469
http://www.wirelessforums.org

You can try a hard reset. Unplug the power, press the reset button and
hold it while re-applying the power, continue to hold the button for
30 sec

In case you have bricked it. Check this out

http://voidmain.is-a-geek.net/redhat...g_revival.html

About a year ago, i bricked mine (v3.0) playing with OpenWRT firmware.
Don't recall what i exactly did but i brought it back to life. Note
that the flash chip in v3 has different pinout configuration. You may
need a magnifying glass.

cheers






On Dec 16, 12:39 am, utopia14 <utopia14.31o...@no-
mx.wirelessforums.org> wrote:
> My Linksys WRT54G v. 3.0 has a blinking power light. I read on Linksys'
> site that I should update the firmware. Unfortunately, my computer
> isn't even seeing the router.
>
> My modem is connected to the router, and my computer is connected
> through one of the router's ports, but when I ping 192.168.1.1 I'm
> getting a time out.
>
> All my computer can see is the modem. It's like I'm not even connected
> to the router.
>
> Any ideas on how I can fix this? Thanks for any and all help.
>
> ------------------------------------------------------------------------
> View this thread:http://www.wirelessforums.org/showth...lessforums.org

utopia14 <(E-Mail Removed)> hath wroth:

>My Linksys WRT54G v. 3.0 has a blinking power light.

Not good. That usually means there's a checksum failure in the
firmware. You might try reloading it with new firmware.

>I read on Linksys'
>site that I should update the firmware. Unfortunately, my computer
>isn't even seeing the router.

Wanna tell us a bit about what's been done to this router? Attempts
to load alternative firmware perhaps? Juggling wall warts?

Have you tried to reset the router to defaults using the reset button?
You have to hold it down for quite a while (30 sec) in order to do the
reset thing.

After the reset, do the following:
1. Set the IP address of your PC to 192.168.1.10.
2. Run a CAT5 cable between the PC and one of the LAN ports on the
router.
3. Unplug the power to the router. Yes, I said *UNPLUG*.
4. On the PC, run:
ping -t 192.168.1.1
Don't worry about ping failures at this time.
5. Now, apply power to the router and watch the screen. At some
point, it should start responding to the pings. After a few seconds,
it will stop responding. If it works like this, your router can be
resurrected.

6. Use TFTP to upload the latest firmware. Same ritual. *UNPLUG*
the power to the router.
7. From the DOS cmd prompt, run:
tftp -i 192.168.1.1 PUT latest_firmware.bin
8. It should take about 5-15 seconds to upload. When done, leave it
alone until the front panel lights cease flashing. Go get a cup of
coffee or something. Resist the temption to play on the keyboard or
power cycle the router. It takes about 60 seconds.
9. Power cycle the router and try pointing your web browser to:
http://192.168.1.1/

>My modem is connected to the router, and my computer is connected
>through one of the router's ports, but when I ping 192.168.1.1 I'm
>getting a time out.
>
>All my computer can see is the modem. It's like I'm not even connected
>to the router.
>
>Any ideas on how I can fix this? Thanks for any and all help.


--
Jeff Liebermann (E-Mail Removed)
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558