Help!: setup Belkin wireless router on LAN

I have a F5D8230-4 wireless router. I want to hook it up to an
existing LAN and just use it to access that LAN. What I found is:
I can hook it up from a LAN port to the WAN port and access the
internet. HOWEVER, I cannot access a NAS that I have on the LAN nor
can I access the router itself (192.168.0.1)

If I disconect the router from the LAN, I can access the router (yes I
have a password).

I turned off the firewall and allowed remote access to the router but
still no luck.

I think I need to set the router to be an access point but this is all
I can find in the manual about that and I have questions:

"The Router can be configured to work as a wireless
network Access Point. Using this mode will defeat the NAT IP sharing
feature and DHCP server. In AP mode, the Router will need to be
configured with an IP address that is in the same subnet as the
rest of the network that you will bridge to. The default IP address
is 192.168.2.254 and subnet mask is 255.255.255.0."

How do I check the subnet on the other router? If the Belkin router
only allows an IP 192.168.2.* then what do I do if the other router
isn't set for that address? How do I set the other router if, say, its
setting are 192.168.0.1 and mask is 255.255.255.0

HELP!

John

(E-Mail Removed) wrote:
> I have a F5D8230-4 wireless router. I want to hook it up to an
> existing LAN and just use it to access that LAN. What I found is:
> I can hook it up from a LAN port to the WAN port and access the
> internet. HOWEVER, I cannot access a NAS that I have on the LAN nor
> can I access the router itself (192.168.0.1)

By using the WAN port, you are adding a separate network to an existing
network. If you want to use the new router solely as an access point, you
want to connect to a LAN port on the Belkin, and ignore the WAN.

These Netgear instructions are generic enough that they probably apply to
your router.

http://kbserver.netgear.com/kb_web_files/n101496.asp
"Using the WGR614 router as a Wireless Access Point."

Turn off DHCP, set the "WAN address" to something harmless, outside of your
normal subnet, and connect your existing router to the LAN side of the
Belkin, leaving the Belkin WAN connection unused.

--
---
Clarence A Dold - Hidden Valley Lake, CA, USA GPS: 38.8,-122.5

RIGHT ON! THANKS FOR THE HELP!

d...@75.usenet.us.com wrote:
> (E-Mail Removed) wrote:
> > I have a F5D8230-4 wireless router. I want to hook it up to an
> > existing LAN and just use it to access that LAN. What I found is:
> > I can hook it up from a LAN port to the WAN port and access the
> > internet. HOWEVER, I cannot access a NAS that I have on the LAN nor
> > can I access the router itself (192.168.0.1)
>
> By using the WAN port, you are adding a separate network to an existing
> network. If you want to use the new router solely as an access point, you
> want to connect to a LAN port on the Belkin, and ignore the WAN.
>
> These Netgear instructions are generic enough that they probably apply to
> your router.
>
> http://kbserver.netgear.com/kb_web_files/n101496.asp
> "Using the WGR614 router as a Wireless Access Point."
>
> Turn off DHCP, set the "WAN address" to something harmless, outside of your
> normal subnet, and connect your existing router to the LAN side of the
> Belkin, leaving the Belkin WAN connection unused.
>
> --
> ---
> Clarence A Dold - Hidden Valley Lake, CA, USA GPS: 38.8,-122.5