Has anyone tried "fixing" a WRT54G v.3...

that doesn't "rout" anymore? (Good signal output, but no internet)
Thanks all.

---AVG Certified Virus-Free---

"tom" <(E-Mail Removed)> hath wroth:

>that doesn't "rout" anymore? (Good signal output, but no internet)
>Thanks all.

Yes, I've tried fixing a WRT54Gv3. Well, actually it was a v3.1. I
succeeded by punching the reset button and starting over with the
settings. Does that help?

--
Jeff Liebermann (E-Mail Removed)
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558

Thanks, Jeff...I've done all of the obvious things, including factory reset.
I'm just getting real sick of replacing this router every year or
so...(sigh)

--
---AVG Certified Virus-Free---
"Jeff Liebermann" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
> "tom" <(E-Mail Removed)> hath wroth:
>
>>that doesn't "rout" anymore? (Good signal output, but no internet)
>>Thanks all.
>
> Yes, I've tried fixing a WRT54Gv3. Well, actually it was a v3.1. I
> succeeded by punching the reset button and starting over with the
> settings. Does that help?
>
> --
> Jeff Liebermann (E-Mail Removed)
> 150 Felker St #D http://www.LearnByDestroying.com
> Santa Cruz CA 95060 http://802.11junk.com
> Skype: JeffLiebermann AE6KS 831-336-2558

"tom" <(E-Mail Removed)> hath wroth:

>Thanks, Jeff...I've done all of the obvious things, including factory reset.
>I'm just getting real sick of replacing this router every year or
>so...(sigh)

Then try the non-obvious things. The usual goof is to not hold down
the reset button for 30 seconds continuously. After 30 seconds of
holding down the button, let go. Then wait at least another 30
seconds for the processor to do something or other. You can tell that
it's done when the front panel light show stops. Wait a bit longer
and then unplug the power. Wait about 10 seconds, plug the power back
in, wait until it boots, and try it with the default IP (192.168.1.1)
and default password (admin). This may sound like a bit of an ordeal
but it's guaranteed to work by avoiding some of the possible
complications.

I also had one local person send me their allegedly dead WRT54G for
repair. The wall wart had obviously overheated and was belching 6VDC
with about 2VAC on top of it. It would light up but hang almost
immediately. Check the wall wart with a volts-guesser.

Lots of other things to go wrong. I've seen bent pins in the ethernet
(RJ-45) jacks, creative wiring, reloading bad saved settings after a
firmware update, and trashed flash RAM.

If this is a regular occurrence, I suggest you someone with a clue do
a detailed autopsy on the carcass to determine the cause of the
problem. I had one customer blow up all kinds of network hardware
because their do-it-thyself PoE injector managed to sometimes go
insane.

Incidentally, "does not route" is far to vague to offer much of a
suggestion. If you can see the web configuration interface, it's
unlikely that there's something blown. Verify that you have the
latest firmware, setup the router from scratch, and try again.

--
Jeff Liebermann (E-Mail Removed)
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558

--
---AVG Certified Virus-Free---
"Jeff Liebermann" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
> "tom" <(E-Mail Removed)> hath wroth:
>
>>Thanks, Jeff...I've done all of the obvious things, including factory
>>reset.
>>I'm just getting real sick of replacing this router every year or
>>so...(sigh)
>
> Then try the non-obvious things. The usual goof is to not hold down
> the reset button for 30 seconds continuously. After 30 seconds of
> holding down the button, let go. Then wait at least another 30
> seconds for the processor to do something or other. You can tell that
> it's done when the front panel light show stops. Wait a bit longer
> and then unplug the power. Wait about 10 seconds, plug the power back
> in, wait until it boots, and try it with the default IP (192.168.1.1)
> and default password (admin). This may sound like a bit of an ordeal
> but it's guaranteed to work by avoiding some of the possible
> complications.
>
> I also had one local person send me their allegedly dead WRT54G for
> repair. The wall wart had obviously overheated and was belching 6VDC
> with about 2VAC on top of it. It would light up but hang almost
> immediately. Check the wall wart with a volts-guesser.
>
> Lots of other things to go wrong. I've seen bent pins in the ethernet
> (RJ-45) jacks, creative wiring, reloading bad saved settings after a
> firmware update, and trashed flash RAM.
>
> If this is a regular occurrence, I suggest you someone with a clue do
> a detailed autopsy on the carcass to determine the cause of the
> problem. I had one customer blow up all kinds of network hardware
> because their do-it-thyself PoE injector managed to sometimes go
> insane.
>
> Incidentally, "does not route" is far to vague to offer much of a
> suggestion. If you can see the web configuration interface, it's
> unlikely that there's something blown. Verify that you have the
> latest firmware, setup the router from scratch, and try again.
>
> --
> Jeff Liebermann (E-Mail Removed)
> 150 Felker St #D http://www.LearnByDestroying.com
> Santa Cruz CA 95060 http://802.11junk.com
> Skype: JeffLiebermann AE6KS 831-336-2558


Thanks again, Jeff. I did a third reset (probably not pressing button for 30
seconds, but it seemed like a eternity) and it's been working fine now for
several hours. Keeping fingers crossed. BTW, I never could access the web
configuration interface after my first two attempts.

So that got me to thinking: could I possibly revive/reset my ol' (2-yr-old)
BEFSW? But there was no way....that one's a goner!

"tom" <(E-Mail Removed)> hath wroth:

>Thanks again, Jeff. I did a third reset (probably not pressing button for 30
>seconds, but it seemed like a eternity) and it's been working fine now for
>several hours. Keeping fingers crossed.

It will probably be fine now. I've had a few weird things happen in
the last few years, where a normally working router just decides to
play dead. 2 weeks ago, I had a Buffalo WHR-G54S suddenly become
inaccessible. No web page, no traffic, no wireless, no nothing. Punch
the reset, reload the saved settings, and it's back. No clue exactly
what happened but my guess is that the router settings were trashed by
something.

>BTW, I never could access the web
>configuration interface after my first two attempts.

Sounds much like what I had happen. Different router, but same
chipset.

>So that got me to thinking: could I possibly revive/reset my ol' (2-yr-old)
>BEFSW? But there was no way....that one's a goner!

BEFW11S4? Why would you want to do something like that? The v2
version tends to loose its settings. The v4 version tends to hang
without provocation. Both fail various router exploits tests. It
only does 802.11b, not 802.11g. It's worth a try, but even working,
it's not a very good wireless router.

--
Jeff Liebermann (E-Mail Removed)
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558