Dlink DWL-G800AP as Repeater ... Need some Advice

I am trying to use a DWLG800AP as a repeater.
The config goes fine, set to repeater mode, finds the AP etc.

However when I set it up, the clients can see it and the signal is great but
they cant get an IP from the AP.

I am using a DI-624 AP and DWLG120 clients.

I would love any tips from amyone else using a G800AP

"news.newsguy.com" <(E-Mail Removed)> wrote:
>However when I set it up, the clients can see it and the signal is great but
>they cant get an IP from the AP.

If you watch the traffic counters, do you see transmit packets but no
receive packets? That's the problem I'm getting with my G800APs...

[There's a promised firmware upgrade due the end of this month, but I
can't get anyone to admit it, as D-Link's tech support has a policy of
being as unhelpful as possible, and referring all "difficult"
questions to their phone support.]

--
William Smith
ComputerSmiths Consulting, Inc. www.compusmiths.com

<William P.N. Smith> wrote in message
news:(E-Mail Removed)...
> "news.newsguy.com" <(E-Mail Removed)> wrote:
> >However when I set it up, the clients can see it and the signal is great
but
> >they cant get an IP from the AP.
>
> If you watch the traffic counters, do you see transmit packets but no
> receive packets? That's the problem I'm getting with my G800APs...
>
> [There's a promised firmware upgrade due the end of this month, but I
> can't get anyone to admit it, as D-Link's tech support has a policy of
> being as unhelpful as possible, and referring all "difficult"
> questions to their phone support.]
>
> --
> William Smith
> ComputerSmiths Consulting, Inc. www.compusmiths.com

If you're seeing transmitted packets, but not received packets, then you
haven't associated with the AP. Turn off WEP and WPA. Reboot everything.

Ron Bandes, CCNP, CTT+, etc.

I am not sure what you are referring to...
Where/how wou;d Isee these


"Ron Bandes" <RunderscoreBandes @yah00.com> wrote in message
news:hmvAc.252$%(E-Mail Removed). ..
> <William P.N. Smith> wrote in message
> news:(E-Mail Removed)...
> > "news.newsguy.com" <(E-Mail Removed)> wrote:
> > >However when I set it up, the clients can see it and the signal is
great
> but
> > >they cant get an IP from the AP.
> >
> > If you watch the traffic counters, do you see transmit packets but no
> > receive packets? That's the problem I'm getting with my G800APs...
> >
> > [There's a promised firmware upgrade due the end of this month, but I
> > can't get anyone to admit it, as D-Link's tech support has a policy of
> > being as unhelpful as possible, and referring all "difficult"
> > questions to their phone support.]
> >
> > --
> > William Smith
> > ComputerSmiths Consulting, Inc. www.compusmiths.com
>
> If you're seeing transmitted packets, but not received packets, then you
> haven't associated with the AP. Turn off WEP and WPA. Reboot everything.
>
> Ron Bandes, CCNP, CTT+, etc.
>
>

"news.newsguy.com" <(E-Mail Removed)> wrote:
>I am not sure what you are referring to...
>Where/how wou;d Isee these

Network and Dialup connections, right-click on conection of interest,
goto Status.

--
William Smith
ComputerSmiths Consulting, Inc. www.compusmiths.com

"Ron Bandes" <RunderscoreBandes @yah00.com> wrote:
>If you're seeing transmitted packets, but not received packets, then you
>haven't associated with the AP.

Or the AP is wedged due to firmware bugs. Repeatable (pardon the pun)
DWL-G800AP firmware bugs.

> Turn off WEP and WPA. Reboot everything.

None of them are on. Yes, rebooting the AP works, but that's hardly
an answer.

--
William Smith
ComputerSmiths Consulting, Inc. www.compusmiths.com