D-Link AP in Bridge mode

Just a simple question:

What should I expect to see when 2 D-Link APs are actually
communicating in bridge mode?

Do you see one bridge appear as a connected PC on the other bridge?

The reason I ask is because I'm trying to get 2 bridges to talk to
each other, but am not sure how to tell when it happens.

The APs are DWL-2000+.

Thanks.

On Thu, 03 Feb 2005 23:54:03 GMT, ButteredMuffin <(E-Mail Removed)>
wrote:

>Just a simple question:
>
>What should I expect to see when 2 D-Link APs are actually
>communicating in bridge mode?
>
>Do you see one bridge appear as a connected PC on the other bridge?
>
>The reason I ask is because I'm trying to get 2 bridges to talk to
>each other, but am not sure how to tell when it happens.
>
>The APs are DWL-2000+.
>
>Thanks.
I have 2 900AP+ setup in bridge mode and no they do not come up
anywhere except their individual setup screens that are tied to their
ip addresses. I know they are working because when I plug a computer
into the one in the basement and it goes on the net, then the bridge
is working. I do not have any wires from bridge to bridge so if the
computers are on the net, then the bridge is working.

On Fri, 04 Feb 2005 01:15:23 GMT, f/fgeorge <(E-Mail Removed)>
wrote:

>On Thu, 03 Feb 2005 23:54:03 GMT, ButteredMuffin <(E-Mail Removed)>
>wrote:
>
>>Just a simple question:
>>
>>What should I expect to see when 2 D-Link APs are actually
>>communicating in bridge mode?
>>
>>Do you see one bridge appear as a connected PC on the other bridge?
>>
>>The reason I ask is because I'm trying to get 2 bridges to talk to
>>each other, but am not sure how to tell when it happens.
>>
>>The APs are DWL-2000+.
>>
>>Thanks.
>I have 2 900AP+ setup in bridge mode and no they do not come up
>anywhere except their individual setup screens that are tied to their
>ip addresses. I know they are working because when I plug a computer
>into the one in the basement and it goes on the net, then the bridge
>is working. I do not have any wires from bridge to bridge so if the
>computers are on the net, then the bridge is working.

That's what I was hoping not to hear.

So simply pinging from a computer on 1 end to a computer on the other
should tell me when 'first contact' happens.

Thanks.

On Fri, 04 Feb 2005 07:05:31 GMT, JHC <(E-Mail Removed)> wrote:

>On Fri, 04 Feb 2005 01:15:23 GMT, f/fgeorge <(E-Mail Removed)>
>wrote:
>
>>On Thu, 03 Feb 2005 23:54:03 GMT, ButteredMuffin <(E-Mail Removed)>
>>wrote:
>>
>>>Just a simple question:
>>>
>>>What should I expect to see when 2 D-Link APs are actually
>>>communicating in bridge mode?
>>>
>>>Do you see one bridge appear as a connected PC on the other bridge?
>>>
>>>The reason I ask is because I'm trying to get 2 bridges to talk to
>>>each other, but am not sure how to tell when it happens.
>>>
>>>The APs are DWL-2000+.
>>>
>>>Thanks.
>>I have 2 900AP+ setup in bridge mode and no they do not come up
>>anywhere except their individual setup screens that are tied to their
>>ip addresses. I know they are working because when I plug a computer
>>into the one in the basement and it goes on the net, then the bridge
>>is working. I do not have any wires from bridge to bridge so if the
>>computers are on the net, then the bridge is working.
>
>That's what I was hoping not to hear.
>
>So simply pinging from a computer on 1 end to a computer on the other
>should tell me when 'first contact' happens.
>
>Thanks.
I never used the ping command so can't say but probably. Just go to
network neighborhood and if they can be accessed than it is working.