Cannot Routing To Internet...

Hi, I have W2K3 Server with 2 NICs 1 of them have a Ip=192.168.0.1 and a DCHP
configured to assign addres to my Intranet.
The second NIC, it's connected to a ADSL modem which connect thru PPPoE with
a loggin and password.
I can't configure routing to the rest of my intranet. I follow the steps,
but the Port (PPPoE) doesn't exist. The server connect OK but the Other PCs
Not.
Anybody can help me!!!
Or Point me in some direction (article or something).
Merry Christmas

Assuming you use the server as a router, make sure you assign one default gateway only. That default gateway should be outside NIC. Or post the ipconfig /all here.

Bob Lin, MS-MVP, MCSE & CNE
Networking, Internet, Routing, VPN Troubleshooting on http://www.ChicagoTech.net
How to Setup Windows, Network, VPN & Remote Access on http://www.HowToNetworking.com
"Nando_uy" <(E-Mail Removed)> wrote in message news:4E436255-9784-45DA-9A95-(E-Mail Removed)...
Hi, I have W2K3 Server with 2 NICs 1 of them have a Ip=192.168.0.1 and a DCHP
configured to assign addres to my Intranet.
The second NIC, it's connected to a ADSL modem which connect thru PPPoE with
a loggin and password.
I can't configure routing to the rest of my intranet. I follow the steps,
but the Port (PPPoE) doesn't exist. The server connect OK but the Other PCs
Not.
Anybody can help me!!!
Or Point me in some direction (article or something).
Merry Christmas

Yes, I use the server as a router, then, how can I assign the default gateway?
Many Thanks

"Robert L [MS-MVP]" wrote:

> Assuming you use the server as a router, make sure you assign one default gateway only. That default gateway should be outside NIC. Or post the ipconfig /all here.
>
> Bob Lin, MS-MVP, MCSE & CNE
> Networking, Internet, Routing, VPN Troubleshooting on http://www.ChicagoTech.net
> How to Setup Windows, Network, VPN & Remote Access on http://www.HowToNetworking.com
> "Nando_uy" <(E-Mail Removed)> wrote in message news:4E436255-9784-45DA-9A95-(E-Mail Removed)...
> Hi, I have W2K3 Server with 2 NICs 1 of them have a Ip=192.168.0.1 and a DCHP
> configured to assign addres to my Intranet.
> The second NIC, it's connected to a ADSL modem which connect thru PPPoE with
> a loggin and password.
> I can't configure routing to the rest of my intranet. I follow the steps,
> but the Port (PPPoE) doesn't exist. The server connect OK but the Other PCs
> Not.
> Anybody can help me!!!
> Or Point me in some direction (article or something).
> Merry Christmas

Nando,

I've done something similar and I sorted by using NAT instead of the DHCP.
NAT is a service which runs under the "remote access/VPN" service.

NAT does lease IP's to clients who broadcast a request for an IP to a DHCP
server so it does the job fairly well.

Fernando.


"Nando_uy" <(E-Mail Removed)> wrote in message
news:4E436255-9784-45DA-9A95-(E-Mail Removed)...
> Hi, I have W2K3 Server with 2 NICs 1 of them have a Ip=192.168.0.1 and a
> DCHP
> configured to assign addres to my Intranet.
> The second NIC, it's connected to a ADSL modem which connect thru PPPoE
> with
> a loggin and password.
> I can't configure routing to the rest of my intranet. I follow the steps,
> but the Port (PPPoE) doesn't exist. The server connect OK but the Other
> PCs
> Not.
> Anybody can help me!!!
> Or Point me in some direction (article or something).
> Merry Christmas